Capacities*
| Material Type | Shape | Max. Section Size | Minimum Suggested ID ¹ |
| Flats, Hard |  |
2-3/4 x 1/2 in / 70 x 12 mm | 28 in / 710 mm |
| Flats, Easy |  |
4 x 1 in / 100 x 25 mm | 26 in / 660 mm |
| Square Bar |  |
1-1/2 in / 40 mm | 20 in / 500 mm |
| Angle, Leg-Out |  |
2-1/2 x 5/16 in / 70 x 7 mm | 30 in / 760 mm |
| Angle, Leg-In |  |
2 x 5/16 in / 60 x 7 mm | 30 in / 760 mm |
| Tee, Leg-Out |  |
2-1/2 x 5/16 in / 70 x 7 mm | 26 in / 660 mm |
| Tee, Leg-In |  |
2 x 5/16 in / 60 x 7 mm | 26 in / 660 mm |
| C, Legs-Out |  |
4 x 1-3/4 in / 100 x 50 mm | 28 in / 710 mm |
| C, Legs-In |  |
3 x 1-3/4 in / 85 x 45 mm | 28 in / 710 mm |
| Round Bar |  |
Ø1-3/4 in / 45 mm | 20 in / 500 mm |
| Pipe, Schedule 40 ² |  |
Ø2 in / 50 mm | 24 in / 610 mm |
| Round Tube ² |  |
3 in / 75 mm x 14 Ga. | ——————– |
| Square Tube ³ |  |
2-1/4 in / 60 mm x 11 Ga. | ——————– |
| Rectangular Tube ³ |  |
2-1/2 in / 75 mm x 1-1/4 in / 30 mm x 11 Ga. | ——————– |
| I-Beam, EZ |  |
S4 x 7.7 in / 100 x 50 mm | 30 in / 760 mm |
*with standard equipment
Rev.0 05/2014. (1.) Minimum suggested internal diameter applies to maximum section size as listed at left. (2.) Set of three rolls required for each tube and pipe size. (3.) Special rolls may improve results on these profile. (4.) Special Beam On-Edge Traction Device required. (5.) With standard equipment. This chart indicates minimum suggested inside diameter with maximum profile size, using mild steel rolling generally in multiple passes. Custom tooling for some profiles may be required for volume production and minimum rolling diameters are limited to level of acceptable deformation. The manufacturer and Carell Corporation reserves the right to revise design, construction and specifications without prior notice. Ratings based on material yield on 36KSI. Machines with extended or shortened shafts are available. Series 3000 machines are designed compliant with ANSI B11.12.1996 standards. The employer of the operator is responsible for providing and insuring the usage of point of operation guards and/or properly applied and adjusted point of operation safety devices are required to meet OSHA, state and local safety requirements.
Specifications
| Section Modulus | 0.61 in³ / 105 cm3 |
| Rolling Speed | 20 FPM / 5.2 MPM |
| Power Output | 4.7 HP / 3.5 Kw |
| Key Width | 3/4 in / 18 mm |
| Roll Diameters | 8.07 in / 205 mm |
| Shaft Diameters | 2.36 in / 60 mm |
| Approximate Weight | 2,420 lbs. / 1,090 kg |
| Total Shaft Height | 2.5 in / 65 mm |
| Useable Shaft | 5 in / 125 mm |
| Thread Length | 2-7/8 in / 73 mm |
| Shaft OD | 2-3/8 in / 60 mm |
| Overall Roll OD | 8-1/8 in / 206 mm |
Standard Features
| Dual LED Digital Displays monitor bending roll positions. |
| Double Pinch Geometry permits pre-bending of leading & trailing ends of the profile without removal from the machine. |
| Telescoping modular multi-component roll set specifically designed to bend standard sections including angle leg-in/out and square/rectangular tube, as well as other shapes in a variety of material types. |
| Tri-Directional Lateral Guides with cam rollers for correcting inherent twist when rolling angle leg-in. |
| Operates in both horizontal and vertical orientations. |
 |
 |